Whirlpool Washer Won’t Spin. The reason a washer spins rather than utilizing any other motion is that it’s the most effective way to create items that are sparkling clean.
Agitation is vital if you want things to be thoroughly cleaned, and this movement dissolves dirt exceptionally well. That’s why spinning is so essential for stain-free laundry.
Spinning also plays a role in draining your clothes of excess water during laundry so they can be dried more effectively.
Whirlpool Washer Won’t Spin
Shift Actuator Fail
Another common issue with Whirlpool top-loading machines has to do with the machine’s transmission/gearshift. It is responsible for shifting between the wash cycle’s spin and agitate modes.
It also counts the number of times that your washer’s basket has spun by means of a sensor which is located on the washing machine’s direct-drive motor housing.
If this pulley belt snapped, the machine would no longer be able to switch between wash cycles or complete both its agitation and rinse cycles. This problem prevents your washer from working properly.
Lid switch failure
Older top-loading washing machines used a lid switch as a safety precaution. This ensured that the machine wouldn’t start spinning if the lid wasn’t closed and if the washing machine is equipped with this type of machine.
There will be an extra piece of metal mounted underneath the washer lid. A pin would slide into the hole of this switched metal, which acted as a magnetic field sensor.
Basket Drive Issue
The basket drive is the small unit attached to the bottom of the inner tub. It makes it possible to engage with transmission and spin even though it’s located on top of the latter.
If you can magnetize and spin the transmission and outer tub, and then the basket only spins slowly or does not spin at all, it could be because either one of two things one there’s damage caused to your basket drive indicated by worn or stripped parts like tabs or a block made for contact. There’s damage caused to your spin tube.
If this is true, you must replace any damaged parts as soon as possible before they prevent you from making further progress in your project.
Motor Board Controller
The machine motor provides power to the machine. If the motor is not functioning properly, this may indicate a problem with the machine’s motor or possibly with its motor control board.
For this particular problem, it is recommended that you first ensure that the machine motor has power by using a multimeter read of resistance between the machine’s end-stop A and B terminals.
Door Latch Problem
The door latch secures the washer door shut during operation. Once the washer door is shut, the washing machine can proceed to its cycles.
If the washer door is not latched shut, the door switch will prevent it from operating. The door latch can fail either mechanically or electrically. Inspect for damage on any part of the latch. If it’s damaged or does not close properly, replace it.
To determine if something has caused the failure with this component, use a multimeter to test any switches involved in this process for continuity.
If one of these switches does not have continuity when activated, then that’s because that’s clearly one issue that’s occurring due to the lack of connection that would happen normally via electricity passing through there hence causing a short-circuit – so simply just replace this dysfunctional switch within it.
Defective Tub Bearing
The tub bearing is located in the middle of the outer tub. The bearing is used to spin the inner tub of your machine smoothly.
If you are not satisfied with how well it performs, you might be required to replace the entire assembly. It takes some knowledge and expertise to diagnose this issue.
If you are looking for repair services, we suggest consulting a professional who will have all the necessary equipment needed to determine what exactly is wrong with your machine before they proceed with any repairs so that any issues do not continue popping up again in the future.
Rotor Assembly Cause
The washer tub rotates because it synchronizes with the appliance’s electrical current to produce a magnetic field.
When the magnet on the inner part of the revolving drum is defective, or there are other misalignments, the washer may fail to spin or agitate.
If you notice any damage or cracks within this area, replace it with a new one.
Coupling Of Motors
The motor coupling connects the washer’s transmission (one of the moving parts which let them agitate) to the motor (one of the big components that make up a washing machine).
When this part breaks on an overloaded machine, it will protect both parts by separating them rather than risking damage. It can also break due to normal wear and tear and needs replacing then as well.
Inspect the part and find out if there is any visible damage like on its mountings or bushings that are essential for keeping it intact.
This might mean you’ll have to replace not just this but other parts as well so take care when ordering one or you might have trouble getting it back together again.
Final Thoughts
If your washing machine is not spinning, you may be tempted to try and fix it yourself. If this all sounds like gibberish to you, then obviously call in a professional instead of making the problem worse than it is.
While most washer issues are easy fixes at home, some more complicated problems will likely need someone with special skills or equipment to solve them. The bottom line, no matter what happens.
If your whirlpool washer won’t spin, there isn’t much point risking serious damage by attempting to repair it yourself.
Related Guides