Whirlpool Washer Won’t Fill With Water

Whirlpool Washer Won’t Fill With Water. The water inlet valve is one of the most important parts of your washing machine. It helps fill your machine, and if any part of it is damaged.

Your appliance won’t be able to fill with water or have the water drain properly. To get your washer functioning again, you will need to replace the inlet valve because it’s broken.

Whirlpool Washer Won’t Fill With Water

whirlpool washer won't fill with water

If your washer doesn’t fill up with water, the likely cause is that a faulty water inlet valve is preventing water from entering the tub. To fix this problem, you will need to replace the damaged inlet valve. The water inlet valve is responsible for letting the water into your appliance. If it’s damaged, the fill function won’t work so it needs to be replaced with a new valve.

In this article, we will discuss how to fix Whirlpool washers that won’t fill with water.

Problems With Water Valves

problems with water valves

The water valve is a small attachment that attaches the hose to the washing machine and controls how much water gets put into the bowl.

For example, a faulty water valve can cause there to be no water input into the tub.

At first, make sure your machine is set on a level area with the detergent dispenser facing out.

After this, use perhaps a voltage tester and test for continuity, making sure it stays at approximately 24V.

If a tester doesn’t work, you will need to replace the entire valve. Another common problem with washers is that sometimes, or if your clothes are really dirty. In this case, check the lid switch.

Electronic Control & Timer

If your Whirlpool washing machine was able to pass the above assessment, it’s safe to say that you have a timer wiring issue. Start with the electrical connections.

Use a multimeter to see if the timer isn’t sending power to the washing and spinning motor circuit and adjust it accordingly.

Defective Lid Switch

defective lid switch

The lid switch on a top-loading washer is a safety feature required on all machines to ensure that the machine won’t turn on with the lid open therefore preventing accidental burns or electrocution for a tiny human.

If the lid switch fails, there is no way of turning off liquid from getting into the washing machine so if there are children nearby please make sure to replace this part as soon as possible.

Detection of water level pressure

Sometimes the level of water can be affected by pressure. According to your model’s internal circuit, there should be a pressure switch component that oversees the water inlet valve that turns it off when the required limit is reached.

Unplug your washing machine, locate the said component behind the control panel and test whether it works as expected with your multi-meter by following your model’s wiring schematic.

If it runs through an air dome tube reaching all the way down to the tub, then this component should be found close to it – usually under its neighborhood in connection with a sump pump attached right underneath.

Hoses & Screens For Intakes

If the hoses are kinking or crimping, remove them immediately. Any kind of obstruction can cause it to break or puncture, damage the inner workings of your washer and possibly ruin it once and for all.

If there is no damage, you might want to be sure that the inlet hose has a clean filter on it. Also, check for particles that could be creating blockage anywhere at all in the hose.

When you reconnect your hoses make sure they’re nice and secure so as not to come loose and leak water or cause any other problems.

Then turn your faucets back on and make sure there is good water pressure coming from both sides.

If everything seems fine with this then you will want to make sure that an inside valve that connects to the same source did not somehow get broken off or interrupted while unthreading your washer during installation.

Final words

If you happen to notice that your washing machine is malfunctioning, what’s great is you know exactly where to look in order to ensure it starts working properly again.

Even if the problem isn’t a serious one (e.g., the program doesn’t work or the water level switch has a high resistance) then simply opening the faucet for a few seconds or clearing any residual dirt itself may be good enough to make things start running normally again.

Whirlpool Washer Won’t Fill With Water

Related Guides

Leave a Comment