Whirlpool refrigerator water dispenser not working. Refrigerator water dispensers are a convenient way to get a great-tasting glass of ice and filtered water at the press of a button. However, many times these dispensers stop working seemingly out of nowhere, leaving us high and dry.
Before we know it, this lack of drinkable water leaves us parched for days on end, until we finally decide to seek out professional help. Why does my Whirlpool refrigerator’s water dispenser keep breaking.
Determine why your refrigerator keeps upping and quitting on you by conducting the right troubleshooting steps to initiate the recovery process and restore your ice-cold supply once more.
Whirlpool refrigerator water dispenser not working
Make sure that you have the right fittings connected to your water source to make sure your project’s life source is secured. Check to make sure there are no kinks in the operating line so you can make sure things remain uninterrupted with your critical flow.
Straighten the operating line if a kink presents itself so you can continue on without any leaks!
Turned on the control lock
Whirlpool dispensers feature a Control Lock feature that prevents accidental usage of all dispenser functions. The dispenser’s display panel will show a lock icon if this feature is enabled.
Check that the Control Lock feature is off if your Whirlpool refrigerator won’t dispense water or ice.
You can turn it off by holding the TO LOCK button for 3 seconds. This feature will be disabled when you see an unlocked icon on the display panel.
Having a clogged water filter
Kinked water filters can lead to the flow of water being restricted and prevent the dispenser from working properly.
Water filters should be replaced about every six months in order to maintain a smooth flow of water and ensure that the quality remains high throughout.
Faulty Door Switch
If the ice and water dispenser stopped working, it may be because of a faulty door switch.
This appliance has a special sensor to help prevent energy loss and keeps track of whether or not the door is closed however, its condition can degrade over time.
It’s easy to check if its condition is damaged if there is no connection between the sensor and the electrical device, it has most likely stopped working completely.
Therefore, if your ice and water dispenser stops working, for this reason, you should fix it as soon as possible.
Defective Dispenser Switch
The dispenser switches send voltage to the dispenser. If one of the dispenser switches is defective, the dispenser will not work.
To determine if a dispenser switch is faulty replace it or test each switch for continuity using a multimeter. If a dispenser switch doesn’t crank then you are set with a new replacement.
Frozen water tube indoor
To determine if the water supply tube is frozen, first make sure to disconnect the tube at the bottom of the door. You can then blow air through it. If air does not pass through, this indicates that the water supply tube is frozen.
If this is the case, you can thaw out your line. In addition, it’s important to ensure that your freezer has been kept at an appropriate temperature.
The freezer temperature should be kept from 0-10 degrees Fahrenheit (or -17.8º C) with a maximum fluctuation of 5 degrees Fahrenheit (+/- 4ºC). And remember: if your freezer gets too cold, this could result in your supply line freezing upon you as well.
Problem with the water inlet valve
The water inlet line opens up to supply water to the dispenser. If the water inlet line is blocked, or the water pressure is too low, the bottle will stay empty and won’t dispense.
The valve needs at least 20 psi to function properly. Make sure there’s at least 20psi of pressure on either side of the water valve! Test your line for continuity if that checks out all right! If not, replace it with a new one.
Concerning the Dispenser Control Board
The dispenser control board oversees most of the functions of the can dispensing system. If it fails, then it may stop supplying power to the whole system.
If only one portion is not working, test each part before testing the entire control board as this would point more clearly to a faulty part than a failing board.
Water pressure from the housing supply is low
There may not be enough water pressure in the home. A minimum of 20 psi is required to operate the water inlet valve that supplies the water dispenser. Make sure that the water flow and pressure are at least 20 psi.
Whirlpool refrigerator water dispenser not working
Related Guides