Samsung Range Stove Oven Troubleshooting. Samsung is a well-established brand in the market, known for its home and office electronics as well as its powerful range of home appliances.
On top of this, Samsung provides top-notch ovens to make your baking experience effortless, but there can be a few problems that impair your baking performance.
Meaning you may have to call upon the help of a reliable service company that deals with repairing Samsung products.
Samsung Range Stove Oven Troubleshooting
This article describes how to troubleshoot some problems with Sumsang range stove ovens.
Samsung Oven Doesn’t Turn On
When the broil element is glowing red hot it means that it is heating up properly. If the broil element does not glow red, then this may indicate that it has stopped working completely.
Faults can occur suddenly, so you need to inspect the broil element for holes or blisters. Then you can use a multimeter to check if the broil element has continuity. If the broil element does not have continuity you will need to replace it as soon as possible.
The thermal fuse trips when the oven gets too hot. If this happens the oven will not turn on. This is not a common occurrence but it does happen from time to time.
In order to determine if the thermal fuse is at fault, you should use a multimeter to test for continuity between the two wires if there is no continuity there could be a problem with the fuse and you should replace it. The thermal fuse cannot be reset if it has blown – once it blows, you must replace it.
Samsung Oven Will Not Turn Off
A relay board is used to control the voltage going to the heating element on some ovens. This relay board has various relays which control the voltage that may show up at specific points in time.
If one or more of these relays fails, then issues may arise concerning the body’s ability to set separate portions of itself into motion, something that would be bad if it continued happening on a continual basis since it might mean harm coming to your loved ones or care provider.
So if this relay board is found to be defective and causing any trouble, you’d be advised to replace the inefficient element(s) as soon as possible.
The oven has control boards that send voltage to the broil and bake circuits based on a user’s settings and sensor input.
If one of the control boards relays short-circuits, it may continue sending electricity to the heating circuit. If your oven continues to heat after it is turned off, it’s likely that your control board is faulty. If this is the case, replace it.
Samsung Oven Won’t Heat Up
The gas oven’s safety valve is essential as it allows the oven to function properly by relaying gas. In most cases, this isn’t the problem when an oven isn’t coming to heat.
The first step one should take is testing all of the other more commonly defective heating components, such as the igniter.
If all of the other heating components are working properly and there are still issues with heating, test for continuity using a multimeter on the safety valve. If there is no continuity in that area, then it’s necessary to replace it.
Ignition coils are the most commonly defective part of an oven that doesn’t heat. The ignition coil draws electricity through the oven’s safety valve to make sure it is open and allows gas to expand and burn inside.
If the ignition coil becomes weak, it won’t be able to open the safety valve correctly, in turn preventing your oven from heating up.
You can easily see if an ignition coil is defective as soon as your oven turns on and heats up, notice if the glow remains lit for more than 90 seconds without igniting a gas flame. If the ignition coil is faulty, replace it.
Samsung Oven Light Went Out
The touchscreen controls the light in your oven. If the touchscreen is broken, it won’t signal the oven control board to turn on the lights, but this rarely happens.
The first test is to see if the light bulb, socket, and switch are working properly. If they’re fine and none of these components has broken or is defective, then there’s a higher probability that it might be something with the touchscreen.
Either the transformer isn’t working right or it’s not being used for what it was designed for. Again, this is rarely a problem but if this does happen you checkout your bulbs and light switch and then move on to testing the transformer. If neither of those checks out you may want to think about replacing them.
Samsung Range Burners Always Spark
The spark module provides power for the individual burners across your surface. If the spark module goes out, it may cause the burners to go out unexpectedly.
However, this is often caused by another component of your appliance namely the spark ignition switch. Before replacing the spark module, try testing your appliance’s ignition system to confirm that this is indeed where the fault lies. If everything checks out with your spark ignition switch then feel free to replace the entire sparks module.
Samsung Range Stove Oven Troubleshooting
Related Guides
my control board has a message (SE) . What does this mean? Also it beeps every 5 to 10 minutes. You cannot use the control board at all.