Roper Refrigerator Troubleshooting. Although Roper refrigerators are generally very reliable, they can stop working at any time, and when that happens, the food inside can spoil quickly.
Troubleshooting Roper refrigerator problems often requires a service person, but if you’re an informed homeowner, there are many preventative maintenance tasks you can perform to ensure that your appliances work properly.
Thus, your time and money can be saved for another time-critical project. Additionally, you won’t have to wait for help during otherwise stressful times.
Roper Refrigerator Troubleshooting
Here are some troubleshooting tips for roper refrigerator problems.
Roper Refrigerator Won’t Defrost
The main control board is the brain of the refrigerator. It tells the defrost system to defrost and tells the light bulb to come on.
If the main control board isn’t working, it is likely that both of these commands will fail to register and that things inside your refrigerator will never be cool enough and will eventually spoil.
If you suspect something may be wrong with your main control board, don’t mess around.
Make sure you check everything else in the fridge first since it’s very possible that something far lower on the list of parts has malfunctioned rather than the control board itself.
Defrost heater assembly work to melt any frost that might have accumulated on the evaporator.
If the defrost heater assembly is defective, the defrost system will not work and you will continue to accumulate frost on your business’ evaporator coils.
To determine if the defrost heater is defective, use a multimeter to test for continuity. If there is no continuity for your defrost heater replacement should be sought.
Roper Refrigerator Leaks Water
Water inlet valves are intended to transmit water from a household plumbing system into the refrigerator.
In order for the ice maker and dispenser to dispense water, the valve must be consistently closed (tight) so water can enter into their respective delivery systems.
Inspect the valve for any holes or cracks around its perimeter, and ensure that it is firmly secured to the house’s water supply line by tightening its mounting bracket screws if applicable.
The water filter may not be attached properly to the water filter housing. If the water filter is not attached properly, water may leak from the filter and possibly damage your appliance.
Remove the filter and reattach it carefully; check to see where you attached it previously to ensure that it is secured tightly this time.
Roper Refrigerator Froze Food
The damper on top of the refrigerator magnetically opens and closes to let cool air into the refrigerator compartment.
Open too wide, though, and it may take in outside air along with cold air that could make your food spoil faster.
Damper issues are usually caused by a magnet or dial being damaged; when you unplug the appliance, pop out the plastic covering over the damper and inspect it for damage such as dents, holes, or cracks.
If you find any damage, check other similar models to see what their dampers look like so you can purchase a replacement as needed.
The thermistor measures the air temperature in the refrigerator and sends the readings to the back panel.
With these readings, it is able to adjust power in order to keep the temperature at a healthy level. If this bulb does not work properly, your gadget will either be too cold or too hot, so you need to know if it’s defective beforehand.
Properly check it using a multimeter and make sure that your refrigerator’s temperature changes accordingly. It might be time to replace the device.
Roper Refrigerator Won’t Cool
A start capacitor is a component of the circuit board of a fridge that provides enough power to start the compressor. Without this, it would be very difficult for your refrigerator to function.
If your fridge isn’t turning on, it could be due to a defective or faulty start cap. Test your start cap with a multimeter and replace it if necessary.
The start relay is responsible for making sure that the compressor is used for the refrigerator starts up when it’s supposed to.
The coolant coil located right above the compressor is where all of the magic takes place.
What happens is that when you open and close the refrigerator door, a magnet in the door and one located inside of the door frame alternate to create an electromagnetic field that turns on a second relay.
This second relay then closes a circuit with pins inside of it completing connection points known as Run and Start which flips yet another relay known as Start Relay that starts the compressor until it’s turned off by either turning off or opening up your refrigerator door again.
Roper Refrigerator Troubleshooting
Related Guides