Maytag washer not draining. Most people have had the Maytag washer at least once in their lifetime. The common faults with Maytags are caused by an interruption in the flow of water.
These interruptions could be created because of many reasons. The most common culprits are a clog or kink in the drain hose (the washing machine’s ‘gut’) or a malfunctioning pump that may be filled with lint or some other kind of foreign object.
You can fix these problems by calling service technicians who can help you solve this problem and teach you how to use your appliance properly.
Maytag washer not draining
Why My Washing Machine Won’t Drain. An obstructed drain hose is one of the most common causes for a washing machine to not drain completely.
Both kinks and blockages can obstruct the washing machine hose, preventing proper draining.
However, if your washer is leaking, it’s likely the clog has cut through the washing machine hose, requiring a replacement.
A kinked or clogged drain hose
A clogged or kinked hose can be the cause of your home appliance not draining. In this case, it’s best to first disconnect the hose from the washing machine and then straighten it out by hand.
It may also be necessary to unclamp the other end of your drainpipe in order to inspect for blockages. Examine both ends of the hose thoroughly; if you are unable to remove a blockage, one end should be removed at its connection to the drain pipe.
If there is damage or when removing one end of the hose causes further damage, it is recommended that you replace that portion or entire hose with a new one.
Overloaded Maytag washer
Did your clothes come out soaking wet after the wash cycle finished? If so, it might be that a badly balanced washing machine was to blame.
Sometimes very tightly packed loads can make machines unstable, which can affect the spin cycle and leave clothes soaking wet at the end of the wash.
If you’re going to layer your laundry and have a large piece of clothing like a comforter, it’s best to stack your other items vertically on one end.
Yes, this may take up some extra room in your drum but will help prevent your washer from tipping over during the spin cycle and prevent that feeling of having everything come out dripping wet.
Lid switch assembly defective
Top-loading washers may have defective lid switch assemblies. On top-loading washers, draining and spinning will only occur if the lid is properly closed and activates the switch.
Try closing and opening the lid to see if the machine drains and spins. If nothing happens and the switch shows a lack of continuity with multimeter testing on certain models, it may need to be replaced.
Cycle selection error
If your washing machine isn’t spinning off all the water, it could be because you’re using a delicates or hand wash cycle. These cycles have slower spin speeds and no spin at all to avoid harming fragile fabrics like lace.
It might also mean that clothes are not getting dry because they’re still soaking wet at the end of a cycle. In this case, try increasing the spin speed or make sure you really know what you’re washing is able to withstand a stronger spin cycle.
Filters or drain pumps clogged
Most front load washers have a drain pump filter to keep small items from clogging your washer’s pump or drain. If a sock, piece of string, or other item makes it past the filter and blocks the pump, it won’t be able to do its job effectively.
You can avoid this problem by keeping your filter clean and free of debris! A commonly overlooked place for these blockages is the mesh tubing attached to the drain pump.
This mesh trap collects particles like lint that are too big for the filter. Check along this tube behind your appliance and remove any items you find there – chances are you’ve cleaned out your filter without removing the blockage behind it.
Problem with the water pump belt
In some older washing machines, belts are used to drive the pump up and down as well as rotate it. It is a very important part of the washer.
So if it breaks or becomes worn out, it shouldn’t be neglected! If you notice any cracks or fraying, replace them right away to avoid costly repairs and other issues that can arise from their failure.
Faulty Door Lock
Damage to the door strike assembly should be checked. Replace it if it is damaged or broken. You cannot fix a damaged or broken door strike; you need to replace it entirely with a new assembly.
Defective Coin Trap
Washers may have a coin trap to catch any foreign objects that enter the drain. In order to avoid any problems in the future, it is important to check this frequently and make sure it is clean.
It might be time for something new if even after cleaning your washer’s coin trap multiple times, you still notice some level of malfunction in your washer draining properly or not draining at all, as normal. Please contact tech support for suggestions and workarounds until you are able to find a solution.
Maytag washer not draining
Related Guides