Maytag Washer Not Completing Cycle. Washing machines are not always the easiest things to work with. Yet, they are still an essential household appliance every family should have. Sometimes you come across a situation where your washing machine stops mid-cycle, full of water.
If your washer has power and it’s closed then check the lid switch by looking for the latch that is used to engage the lid to press down on it one time.
This will either let it resume or take you through one cycle sequence until you can diagnose what’s wrong with your washer.
Maytag Washer Not Completing Cycle
If the door lock is defective, the washer may stop mid-cycle. The door lock can fail either in a mechanical or an electrical fashion.
Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it.
Drive Belt Damaged
If the aforementioned fixes don’t work and you still can’t get your Maytag Bravos washer to spin, there might be a belt problem. The majority of Maytag Bravos washers include two pulleys on which the belt sits, one for each end of the drum.
The belt is suspended between these pulleys and helps to hold up its weight and facilitate smooth spinning.
However, after long-term use, drive belts tend to loosen on the pulley-reinforced connections; this can also damage them if they’re not reinforced properly by a solid replacement Maytag clothes dryer drive belt.
If you think the belt has frayed or torn, contact Customer Care for expert advice about whether or not it can be repaired. However, if it’s completely broken, your only option may be a replacement.
Error With Washer Timer
To ensure your washer is operating efficiently and effectively, troubleshoot the timer. The timer provides instructions for your washer, such as when to add different chemicals or when to stop. If you’re washing a load of clothing and the water turns off before all of the soap is removed, it will leave residue in the clothing and the machine.
Also, if you wash a load that requires several water temperature changes throughout and one or more temperature changes never happen, this may result in either an incomplete wash or in the chemical residue left in your clothing after drying.
To solve these issues, check the timer for continuity by testing it with a multimeter to determine if there are any problems with your washer’s timer. This part can easily get damaged, but chances are high that it simply went bad over time.
Pump And Motor Issues
If your washing machine stops mid-cycle and is not draining some clothes after the wash is complete, it could be because of a problem with the pump or the motor.
This can’t remove water from the clothes enough for this to work, and thus the sensors won’t allow it to move on to the next cycle.
Typically when such parts fail, you will notice strange sounds (worse when draining, otherwise quiet or very low-pitched), this being a good indicator that there may have been a problem with them all along.
Cleaning A Clogged Hose
If the drain hose becomes clogged, it could stop water from draining properly. If the washer was in mid-cycle it would switch off as soon as the pressure became too strong, preventing more serious problems.
You can check if the problem is a clogged hose by disconnecting it and blowing air through, but you will first need to get all of the extra water out before disconnecting anything to make sure you eliminate any other possible issues.
Main Control Board Problem
The main control board might be defective, but it’s rare. When diagnosing a problem with a microwave that appears to have a faulty main control board, first examine the door switch and inverter above all else.
Defective Lid Switch Assembly
When the lid is open, the lid switch assembly prevents the washer from spinning. Should the lid switch be damaged, the washer will stop halfway through the cycle.
Test the switch continuity on each of the lid switch assemblies using a multimeter to determine if it is defective. Replace any switch that does not have continuity.
Switch And Motor Assembly For Door Locks
The washer door locks the wash tub into place during operation. Once the washer begins to fill, or if it attempts to begin operation, or if a proper water level is reached and a normal cycle is selected, a mechanical lock will retract and the wash cycle can activate.
If this latch is broken or defective, the washing machine will not turn on. Check for any signs of damage on the external parts of the latch/lock first before going deeper to ensure this system works as intended. Clear out any rust or clean up any debris that might be keeping this from locking into place as designed.
Consult your washer’s diagram and use a multimeter to test each of the door lock’s switches for continuity from root to tip from both ends. If one contact is severed from its switch body, replace it immediately with no discussion.
Final Word
Maytag Washer Not Completing Cycle. If you are feeling overwhelmed and do not know where to start when it comes to making repairs, then you should get in touch with professionals.
Our maintenance specialists will help you diagnose any mechanical or electrical problems so that you can prevent further deterioration or even a stopped motor.
This may be the result of defective components, an incorrectly-placed rotor assembly, worn-out spine tube tabs and drive blocks, or burnt-out circuit boards related to the scope’s electronic section which could only be detected by an engineer inspecting the device top to bottom.