Maytag ice maker not working. Most commonly, an ice maker stops working because there is some kind of obstruction within the system. If a blockage does occur, you should use the ice scoop to clear it out.
The best way to know if this is an issue is by inspecting your ice maker regularly to make sure there is no buildup. However, if you don’t have a scoop handy, here is another method that can help dislodge any possible obstructions.
Check and make sure your water filter isn’t clogged or frozen (this could be particularly problematic during the winter months). Another cause of partial or total inoperability of your appliance could be attributed to the valve which allows the water into the unit. Use the following steps to ensure that this doesn’t happen.
Maytag ice maker not working
Maytag ice maker not working. Check that it’s securely connected to the inlet valve and that the tube is not bent or twisted. In some cases, the supply line itself may also become frozen.
If this is the case turn off your refrigerator and remove the waterline. Use a hair dryer to thaw the ice and reconnect it after you’ve cleared out any clogs in its way.
Defective Water Inlet Valve
The water inlet valve is an electrically-controlled valve that allows water to enter the refrigerator and then go to the ice maker. The reason why it’s there is because the ice maker needs water to make ice.
If this valve isn’t working, or if it doesn’t have sufficient pressure, there will be no water for the ice maker to make ice. This can be caused by a variety of reasons, such as low water pressure or an improperly-working valve in general.
Since this needs at least 20 psi to work properly (pounds per square inch), use your multimeter to check on the power flowing through not only the inlet valve but also a part of the pipe supplying it.
What it needs while also ticking into other basic things you might have missed, like cleaning out sediment build-up that could be clogging up this area.
Temperature setting
If the freezer temperature is above 10 degrees Fahrenheit (-12C), the ice maker will not produce ice cubes efficiently. The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15C) for the ice maker to work properly.
If the freezer temperature is too high, ensure that the condenser coils are clear of debris and the condenser fan is working properly.
In addition, check to see if frost has accumulated on the evaporator coils. If you discover frost, it could mean that part of your defrost system has failed.
The ice maker switch might be defective
The ice maker might not be working. It’s possible that the Ice Maker Switch is defective, so you’ll want to start by making sure it is turned on.
If the switch is on, but the ice maker isn’t still making ice, you should check the switch with a multimeter to make sure it has continuity (or “works”). If not, then you’ll want to replace it.`
Replace the ice maker assembly
It’s possible your ice maker is malfunctioning. Luckily, the whole unit isn’t faulty; you just need to replace a few parts and it will be back up and running again in no time.
The first step is to make sure everything is working its part by verifying that the waterline and inlet valve are working correctly and the freezer hasn’t exceeded 15 degrees Fahrenheit.
If they have been working up until now there’s a strong possibility that the ice maker assembly needs replacing.
A clogged water filter
If a clogged water filter prevents the ice maker from working properly, that could mean home to many problems – including water quality.
If you notice that your icemaker seems like it works more slowly than usual, or if your ice cubes seem smaller in size than normal.
This may be the first sign of a clogged water filter (and other related problems). Replacing it is simple and easy.
Ice Level Control Board won’t work
Some refrigerators use a mechanical ice level control switch that senses when the icemaker bucket is full. When too much ice accumulates, the switch opens and tells the refrigerator to stop making ice.
If the icemaker control switch or the wire connecting the control switch to the control board fails, the refrigerator will turn off power to the icemaker. Check if power is reaching both parts if it is, replaces the defective part.
Faulty Icemaker Mold Thermostat
The icemaker mold thermostat is calibrated to shut off the flow of water when the ice mold has reached a certain number of degrees. If this thermostat malfunctions the water will stop flowing and the ice maker will stop making ice.
To test if your thermostat is defective, you first use a multi-meter to determine if it has continuity.
Then, once you have determined that the sculpted figures aren’t connected inside, you take out one of these and replace it with another one (of course you’d buy a new one instead).
The purpose for this is because your refrigerator must generally be colder than 20 degrees Fahrenheit for them to close otherwise things won’t thrive in there.
Problem with Icemaker Module
The icemaker module is equipped with an on/off switch or a bail arm, depending on the model which helps to dispense ice cubes into the ice bucket.
Once the temperature reading of the icemaker feed barrel gets below a certain point and depending on your model, the motor will cycle to release the ice cubes.
At the end of this cycle, it sends power back through to the water inlet valve, allowing it to refill for another batch of frozen treats. If this part of your ice maker is not working as expected, take a look carefully at what might be causing the problem.
Depending on your model, you might have an ejector blade that pushes out any cubes that have failed to fit through.
Maytag ice maker not working
Related Guides