Kenmore Washer Stops Mid Cycle. When your Kenmore Washer stops mid-cycle it can be frustrating because those clothes are never going to get clean.
You can’t just keep washing the same laundry over and over again until you’re satisfied with how clean they are that’s not how a Kenmore Washer works.
Make sure you take them out at some point or it won’t do any good. And if that doesn’t work then there are Appliance Repair service companies that can help you with issues like this one and hopefully sooner rather than later.
Kenmore Washer Stops Mid Cycle
This article discusses some problems with Kenmore washers that stop in the middle of a cycle.
Timer Not Working
A timer in your washer tells it when to stop a cycle.
However, if that timer is malfunctioning, it may do things like displaying the wrong time or not completing a cycle by telling the control board to stop.
If your washer stops in the middle of a cycle or runs indefinitely due to never being told how long a cycle should take, replacing the timer may help solve those problems and get your laundry washing machine running normally again.
Depending on your washer model, you can access and check the timer by removing the back or the control panel.
This is not a part that can be easily damaged, but it can simply become worse with time. You can only solve a problem by testing it with a multimeter.
Valve for the water inlet
You might notice that your washer keeps stopping during the rinse cycle if the water inlet valve is defective.
This problem generally occurs with washers that have hard water since mineral build-up on the filters will cause this to happen much more commonly.
If you notice that your washer’s water pressure seems low or if there are obstructions in the input area of the appliance, then it is likely that there is mineral residue built up on the pipes/filters, and it needs to be cleaned as soon as possible.
Other common culprits include defective solenoid valves and hoses that have become kinked or twisted.
The best way to determine what’s wrong with your washer is to test it using a multimeter and check for continuity in the various parts of the rinse cycle.
Trouble With Clogged Hoses
If your drain hose becomes clogged, your washing machine will cease operation automatically until the problem is fixed.
This helps prevent even more damage to other parts of the unit that could occur if it continues to run and cause flooding.
The best way to check for clogs is to disconnect the hose from the machine and make sure air flows through with ease.
You should also be able to keep a close eye on any potential problems that might occur due to leaks because you will always know where in your home they originated if/when they start occurring as a result of any cracks or damage caused by earlier issues.
Pump And Motor Malfunctioning
If a washing machine stops mid-cycle, it could be an indicator that the pump or the motor running it has failed.
If this happens, the water cannot be pumped out properly, and therefore, the sensors will not allow it to move to a new cycle.
If any part of either of these components fails in your washer’s case, you’ll be able to hear it making sounds and maybe even begin to smell something burning up, which is typically a good indicator of what to check there first.
Assembly For The Lid Switch
It prevents the washer from spinning when the lid is open, among other things. If this switch fails, the machine may stop mid-cycle.
Troubleshooting a non-functioning lid switch involves using a multimeter to see if the switch is still working.
To do this test, you need to set your meter on ohms with a continuity test and touch one lead to each of the terminals of the switch and then check for resistance on either side.
You need to replace the particular switch if there is no continuity.
Faulty Control Board
A warning signal that you may have a problem with your control board is if you have been having problems with many other items in your washer’s wash cycle or any other basics of the washer.
These warning signs are not only indicative of a problem with your control board; they can also alert you to systems such as the timer, electrical cord, and even significant damage to your agitator.
Most often the cause of all these issues will be a faulty control board, but before you replace it, we recommend you ask yourself several questions, including ones like have I noticed anything out of place inside my washer.
Related Guides