Kenmore Dishwasher Won’t Start. The dishwasher is one of the best appliances on the market. It saves time, enhances convenience, and it offers excellent quality. But this doesn’t mean dishwashing is easy.
You run into many problems along the way especially when your products are experiencing difficulties with their functionality.
But there’s nothing to worry about; you can easily troubleshoot some issues yourself if they arise, which is what we intend to show you in our guide for dealing with common problems that tend to occur with these appliances.
Kenmore Dishwasher Won’t Start
Kenmore Dishwasher Won’t Start. The thermal fuse shuts off power to the dishwasher if it overheats. However, there are several other reasons why your dishwasher isn’t starting when you want it to. To determine if the thermal fuse is defective, first test it for continuity using a multimeter.
It is possible for your Kenmore dishwasher to not be working due to a variety of reasons. Here’s a list of some of the most common reasons Kenmore dishwashers stop working.
Defective Water Valve
If the Kenmore dishwasher is not starting, it may be because of a faulty water valve. The water inlet valve supplies hot water to the dishwasher and is controlled by a timer or electronic control. The water inlet valve needs to be kept clean and free of debris so it can work properly.
When the dishwasher is not filling or if you suspect there’s no hot or cold water getting into the machine at all, this could mean that there isn’t enough pressure coming into your house from the hot water source or even just an old hose leak.
To make sure you have enough hot-water supply for your machine and its plumbing system, run another faucet until cold becomes hotter than warm as this will indicate if there’s adequate pressure available at both ends of where things connect on either side of valves like these ones here.
Drive Motor Problem
A dishwasher with a broken drive motor, which is responsible for rotating the inner wash/drying tub, can cause many problems in your model.
If you notice that there are loud humming sounds coming from the motor when it’s turned on, you must find out if this is normal when the tub spins or not. This may help you determine whether to replace the wash motor or check other parts of the machine for an issue.
Usually, these motors utilize two belts to move the motor so if either belt is loose, torn, or broken then the drive motor will begin to make noises upon spinning the next time it runs.
Touchpad Issue
If the Kenmore dishwasher won’t start, the issue may be electrical. Some common symptoms are that the buttons don’t work or they only work if you press them very hard.
If this is what has happened, then there are some other reasons why this could have occurred. Try resetting the dishwasher and unplugging it for a few hours. You should be able to get your Kenmore working properly again with these steps.
If this fails, then you will want to contact the manufacturer or purchase an extended warranty so it can be repaired quickly and easily by someone qualified for this type of fix.
Timer Fault
The timer is responsible for making sure that important things get done at specific times. If the timer fails to operate, then it will fail to start up the dishwasher at the right moment, causing it not to operate at all.
While timers are often given the blame for this type of malfunction, one should make sure there are no other component failures before assuming it’s always the timer causing problems.
Main Board Controlling
The main control unit attached to the dishwasher motherboard provides power to nearly every component of the machine. If there’s any faulty wiring, it’s possible that the dishwasher may not function properly.
Control boards are often misdiagnosed when in fact other components are damaged like faulty wiring or loose connections, so make sure you check all of these when troubleshooting dishwashers that don’t perform as intended.
There Is A Child Lock-on
This is a common problem with Kenmore Dishwashers. Sometimes the child lock can get activated without the owner knowing about it, especially if they have young children in the house or are using their dishwasher at inappropriate times.
To turn off this lock, press the cancel button located on top of your Kenmore for five seconds. If your appliance still won’t start up after doing so, check to ensure there are no other problems preventing it from doing so.
Fuse Thermal
The thermal fuse helps prevent the dishwasher from overheating. If it does overheat, the thermal fuse will stop the appliance from working.
To test the thermal fuse, use your multimeter to check for continuity. If you don’t have continuity, the thermal fuse is defective and should be replaced.
Verify The Selector Switch
You can select different washing, drying, and heating options for a dishwasher’s wash cycle using the selector switch. Your dishwasher may not start if its selector switch is defective or not depressed correctly.
Verify that the selector switch on the control panel of the dishwasher isn’t stuck between settings. Check if you pressed more than one button at the same time. If more than one button has been pressed, there will not be any power to your dishwasher’s selector switch.
(Guide About Kenmore Dishwasher Won’t Start)
Related Guides