Jenn air electric cooktop burner not working. You can fix it by having the surface element replaced by Jenn Air. If you are able to remove the burnt-on food, this will also help avoid having to have the entire surface replaced.
Cleaning can be done in a variety of different ways including vinegar and baking soda.
There has been a lot of mixed reviews so please make sure you research both sides and look into what could happen if you try to clean your stove.
The best approach is contacting Jenn Air representatives as they would know how to most effectively fix your stove based on all their different experiences with different clients and products they have sold and overseen themselves.
Jenn air electric cooktop burner not working
What to do if your Jenn-Air electric cooktop burner doesn’t work here are some common causes and how to fix them.
Problems with incoming power
It’s possible that the range is not receiving the proper voltage.
Electric ranges require 220 volts of alternating current. If the range is receiving significantly less voltage, the surface element won’t work.
To check to see if the outlet has sufficient voltage, use a multimeter to test the outlet’s receptacle and trace down the source of the problem whether it be a wiring or an electrical fault that requires professional attention.
Defective Surface Element Board
the surface element uses the power supply to regulate the circulation of gas flowing through each burner on the stovetop.
If there is a failure with one or more of the relays that regulate this power, only some of the burners will work or not at all.
When two or more burners become inactive at roughly the same time, it indicates that there may be a defect on the surface element board and if only one of your burners doesn’t seem to be able to spark, test for continuity using a multimeter.
If your burner has continuity then your surface element board might be defective.
Faulty Coil Surface Element
First, be sure to put the element in all the way or you’ll likely have a problem with it heating up. If the element doesn’t protrude enough out of the socket, then this could result.
Second, look for signs of damage on the element because if it has such problems then that could interfere with its ability to transfer heat effectively, causing it to break down over time and become lifeless before its time.
Last but not least, test for continuity between the thermocouple and the surface unit by using a multimeter (this is an electrical testing device that one can use to test various parts and devices).
If there’s an issue with continuity being exhibited and your life source is disrupted by such difficulties, that’ll lead you to believe it may not work as efficiently as it could which will end up making things hard on you in due course.
Surface Element Switch issue
The switch that turns on the surface element sends voltage to the surface element coil. If the switch isn’t working properly, then you will get no power from your surface element.
However, if there is a second surface element of the same size on your range, try switching which ones are in use.
If your non-working surface is still not heating up, it’s likely that you need to replace your surface switch.
This part cannot be tested or repaired; if you think this might be an issue with one of your switches, get a replacement.
If the solid surface element won’t work
If a solid surface element refuses to heat up, there are a couple of likely possibilities. What you want to do is make sure that the hot surface element on top of your stove has not burnt out.
As we know, the heating coil inside the solid surface element glows red when it’s turned on and gets hot enough to transfer its heat to the rest of the unit.
If that orb at the top begins turning blue, then it indicates that your actual heating mechanism is getting closer and closer to meeting an early demise which makes sense considering how often they are used.
Oftentimes simply replacing this surface unit with a functioning one will get things back up and running properly.
However, it’s always best to have both units in working order so you don’t ever risk burning yourself so double check if your gas or electric range contains two separate heating mechanisms for each element.
Radiant Surface Element doesn’t have continuity
The most common cause when the surface element does not work is the heating unit itself. The heating unit can burn out similar to a light bulb.
If the surface elements do not work and they don’t have continuity, then it could mean that your heating unit will need to be replaced. The radiant heating unit is not repairable.
Problem with Element Receptacle and Wire Kit
The housing of a surface element plugs into a receptacle. Over time, if the receptacle is used excessively or if it isn’t regularly maintained, the contacts inside can become worn out which will prevent the surface element from receiving power.
To determine if the element is faulty, check for signs that it’s been worn down and then you must replace it.
In addition, also ensure that none of its prongs have been burnt out because if they have you will have to replace both the element and anything it’s attached to.
Related Guides