Husqvarna snowblower troubleshooting. There are a number of snow blowers manufactured by Husqvarna that use two-stage augers and impellers to move snow. The various models have differing specifications but all use the same basic system,
So if you’re unable to correct an issue with your Husqvarna snow blower then it might be worth following the troubleshooting steps outlined for each model below in order to identify whether you need professional repair work done on your device.
Husqvarna snowblower troubleshooting
In this post, we will discuss some of the most common reasons and how to solve them for Husqvarna snowblowers.
The Husqvarna snowblower will not start
Inspect the spark plug for damage or wear. If there is excessive carbon buildup on the electrodes, cracks in the electrode, or the insulator are cracked or chipped, replace it. Spark plug testers can be used to do this.
When you crank the tester, a spark should appear between the terminals. If no spark shows up, inspect your distributor cap to ensure that it isn’t loose and that its contacts are clean and dry.
If this doesn’t work and you’re still having issues with no spark, then check to make sure that all of your connections are secure (distributor cap-to-spark plugs). Finally, verify whether or not your coil has an adequate output at around five volts before trying anything else wrong with it.
Husqvarna snowblower stalls after starting
The level in the fuel tank decreases as fuel is consumed by the engine. To compensate, automakers install a pressure release valve that allows air to get into the tank and maintain pressure.
If the cap becomes clogged, air can’t get into the tank so there’s less pressure which can result in a vapor lock or a lack of power to drive your snow blowers.
Check your owner’s manual to see where your fuel filler cap/vent is located and clean it for any dirt or grime that may be preventing it from closing properly.
If loosening up the cap has no effect on if your engine stays running, repeat this process checking for kinks or tears in the line near the cap.
As fuel ages it can thicken up and if enough sediment builds-up in your gas tank you might need to clean out your fuel system. Another possibility is that there is a faulty gas tank vent valve that needs to be repaired.
Husqvarna snowblowers have poor performance
Be on the lookout for signs of damage or wear on your Spark Plug. If the porcelain insulator is cracked or damaged, or the end connectors are burned away, you should replace the spark plug. Using a spark plug tester, you can determine if a spark plug is defective.
Connect the tester’s terminals and crank your engine to see if you get a good spark on each cylinder. If there is no spark these could be signs that the spark plugs on this engine need to be changed immediately.
It is possible that you overfilled the engine with engine oil. Ensure that you have enough oil in your blower so it doesn’t overflow but just enough oil in all of its spots while maintaining proper levels at all times so you don’t run any risk of having any spillages which seep into any of the fuel injection systems components such as the carburetor for example.
Husqvarna snowblower wheels do not engage
The V-belt connects the engine to the gearbox and keeps the snowblower turning, but failing to change it could lead to a breakdown. If you notice that the V-belt is either out of order or missing, find something similar in size so you can inspect it for any tears to make sure it’s not causing an obstruction.
The friction ring turns the drive plate which then causes the wheels to turn and move forward if this one isn’t working properly you could be stuck with no way around hazards such as snowdrifts.
If your engine won’t start then you should check this first before anything else because even though all other components may look fine, something like this could cause enough of a backlog for other parts on the motor to overheat and fail through frequent use and exposure.
Husqvarna Snowblower auger won’t turn
The cogged belt is used to turn the engine. If the cogged belt is broken, misplaced, or wobbled, the snowblower won’t effectively move. Check this before starting off at all.
It’s very commonplace for mechanical problems to happen (just like on a car). Always check first! If you found that this belt was damaged in any way whatsoever do not hesitate in replacing it with a fresh brand new professional genuine part.
Sometimes cogs can get ripped off if something heavy falls on them. So make sure you check this with care and replace the whole thing immediately if needed.
Related Guides