Husqvarna chainsaw won’t start. Chainsaws are often considered power tools of last resort for owners of large lots because they can cut down trees easily, and with a great deal of accuracy.
If you own a Husqvarna chain saw yourself, then you know how great the tool is at processing wood to be used for things like heat or furniture material.
The best part about owning a chainsaw is knowing that it will only serve you if it’s in tiptop shape.
This means that the chainsaw’s engine must work well throughout its lifetime and that one must have the skills to keep it working properly.
Husqvarna chainsaw won’t start
If you try to start a chainsaw that hasn’t been used in some time but doesn’t have fuel to run it properly, the carburetor might become clogged.
Clogging is often caused by leaving fuel in the chainsaw for too long without using any of it. This sticky gasoline can coagulate and form clumps which, in turn, cause the carburetor to malfunction.
Did the machine turn on?
The engine simply needs to be turned on; ensure that the ignition switch is set to the “On” setting and that they are not damaged or loose in any way, so you can be sure everything is where it needs to be.
Also, check whether the choke lever is set to the “Start” position and there’s a primer bulb (if present) filled with fuel.
Then, pull backward on the front handle this will make sure that the chain brake isn’t engaged because it requires disengaging prior to starting up the device.
Using the Proper Fuel
Husqvarna chainsaws are fuelled with a special type of fuel to ensure they can perform at the level that’s expected of them.
The regular unleaded gasoline, which should be mixed with a high-quality air-cooled two-cycle engine oil; should be mixed at a ratio of 40:1 in a clean fuel container.
Shake the oil and gas together to blend them thoroughly. Dump out any unmixed or old gasoline immediately. Clean the fuel tank with a brush and rag if the gas has gone bad, and pour.
Spark Plug issue
If the Husqvarna chainsaw will not start, it could be because of the electrical components. The spark plug or wiring may have a fault which are both common causes for this.
If you notice that your spark plug is dirty, clean it and firmly tighten it back into place with pliers.
You’re most likely to see an improvement in performance as a result.
However, if you find that your spark plug is faulty then you’ll need to purchase a replacement.
Your Husqvarna chainsaw’s ignition module could also be malfunctioning so take back your chainsaw to your nearest dealer for attention if this is the case.
Defective Carburetor
To get your Husqvarna started, make sure it is fueled properly. First, verify that the fuel line and that is connected to the mower’s tank. Next, turn over your engine with the starter rope so that gasoline fills the carburetor.
This can be verified by looking at the air filter to see if there is gas coming through and filling it.
If you don’t see fuel coming through at all, first try to look at where you have the mower set up with regard to topography because this might be causing trouble getting fuel into the carburetor chamber. Then check for obstructions in your fuel lines.
Ignition Coil problem
The ignition coil sends voltage to the spark plug while the engine is running. If the ignition coil is defective, the engine may not start. Before you replace the ignition coil, make sure that the spark plug is in working condition.
Once you have confirmed that there’s nothing wrong with your spark plug and it’s functioning properly, use an ignition coil tester to detect any issues with your ignition coil before replacing it entirely.
Rewind springs can be replaced
When the starter rope gets pulled and released, the rewind spring will compress and recoils it back onto a pulley. If the starter spring brake is broken, the rope won’t get compressed to a pulley.
As a result, this will cause an engine to be a hard or possibly impossible start. So if you notice your starter rope appears stiff or isn’t winding on your sprocket properly, then it’s best to replace it.
You can do this in two ways You can replace individual parts or do the whole assembly.
Recoil starter assembly is not functioning
The recoil starter assembly is what allows the chainsaw to function properly.
Not only does it start the engine and get it running, but it’s also capable of rewinding in case a piece of wood snaps or if something goes wrong during its operation.
If the starter assembly isn’t working as well as you want it to, then simply replace it with an improved version so that your chainsaws can be up and running right away.
Recoil starter pulley is broken
Retracting the starter rope, a rubber-coated pulley keeps the rope from unraveling when you’re using it to start your engine.
If this pulley breaks or sticks, however, your engine won’t start and neither will your Husqvarna chain saw.
Due to its sensitivity and delicate nature remember to replace it as soon as possible or else you might need a tow truck again.
Husqvarna chainsaw won’t start
Related Guides
