How to hang christmas lights on stucco. Christmas is right around the corner, and for many of you, this means it’s time to start decking the halls with Christmas lights.
Hanging lights on stucco can be somewhat troublesome due to the nature of the surface but we have come up with three methods for hanging Christmas lights to prevent any unnecessary stress during this time!
These include double-sided tape, applying glue to each light socket holding it in place, and attaching your lights with plastic roof clip nails.
How To Hang Christmas Lights On Stucco
To hang the string lights on the wall using hot glue or double-sided tape, you will need to apply some glue onto the back of them and place each bulb individually onto where you want it to go. Find a spot that is not too bumpy or uneven so they don’t come loose.
The following is a guide to putting up Christmas lights on stucco.
By Applying Glue
If your installation of lights has damaged the Styrofoam on the back of the house, then you need to make small holes with a hammer and drill.
Once you have done this, apply some glue in one or more places regarding the light sockets where bulbs have yet to be installed. This will help hold them in place as well as prevent mishaps so that nothing messy happens on top of your stucco.
Create Small Holes In The Plaster
Before someone installs Christmas lights on stucco, make small holes in your home’s stucco with a hammer and drill. This is one of the tips for installing holiday yard decorations on a house made of stucco.
Also before you install holiday lighting on your recently installed stucco home, for example, you should tap lightly along the surface with your finger to test if it has Styrofoam backing.
Check The Plaster For Styrofoam
If your stucco is painted, you should avoid using hot glue. If you don’t know for sure whether or not your plaster contains Styrofoam, you can tap lightly on your stucco to see if it has Styrofoam backing.
Before hanging your lights, you will have to make some small holes with a hammer and drill if there are any holes in the surface of the plaster that would indicate a drill was used previously to hang your lights.
Installing String Lights
Remove all light bulbs from your strings of lights before installing them. As Christmas trees get bigger, it becomes increasingly difficult for homeowners to see once the holidays have come and gone.
It’s often best to not hang the tree too high, should you ever decide to sell the house in the future.
For the best possible results, we highly recommend using an outdoor-rated stringing wire that will help protect bulbs from moisture and prevent them from overheating enough to break or cause a fire.
Bead Glue on Sides
Apply a small bead of glue to the side of your first empty light socket. This will help secure it to the wall for easy hanging as well as not make messes when installing them.
Hold the light socket to your home for a couple of seconds. This will cause an indentation on stucco, which you want for optimum adhesion. Continue installing the light sockets onto your home’s walls until you’ve run out of them or have reached from where you’d like to hang more lights.
This will help keep you on top of things, which will make teamwork easier. The more organized you are at work, the less likely it is that a light bulb will get loose or fall out when someone bumps into them!
Soften the glue with the heat gun to remove the light socket. Once you’re done decorating for Christmas, give your stucco a good scrub and everything should be right as rain.
Applying Double-Sided Tape
You might have issues taking care of the Styrofoam. It is very difficult to remove it when installation is done. So, you need to take your time by watching out for professional advice before removing stucco from your house. It is easy to hang Christmas lights on stucco using double-sided tape.
Cleaning Surface
When trying to install ceiling lights in your home, it is important that you have a clean surface so as not to leave behind any dust or debris.
Leave a spot open on the ceiling where you plan to install the lights, and then make sure all the surfaces of your workspace, including tables, floors, and walls are sparkling before getting started.
Tape The Double-Sided Tape
Attach the double-sided tape to your light bulb socket with green Christmas lights. This will ensure that they stay on when you install them. The more double-sided tape you use, the better it will stick when adhered to multiple surfaces.
Installing Lights
Press your light against the stucco surface, then remove it. This will leave an indentation on the wall that is ready for installation.
The more you use it, the better it will be. To save yourself from stress and double-sided tape accidents by purchase a roll of this stuff at your local hardware store or online.
How To Hang Christmas Lights On Stucco
Related Guides
My bгother ｒecommended I would possibly lіke this web
site. He used to be entirely right. This publish truly
made my day. You can not believe simply how much tіme I
had spent for this information! Thanks!