Hotpoint Dryer Won’t Start. Having a Hotpoint dryer that won’t start is certainly not ideal, but fortunately, there may be many reasons behind the malfunction.
There may be a specific part malfunction that doesn’t allow for the starting of the Hotpoint dryer cycle or it could simply need an adjustment for it to function properly once more.
Either way, using these Hotpoint dryer troubleshooting tips can help you narrow down and fix any issues that might be keeping your appliance from getting back up and running quickly.
Hotpoint Dryer Won’t Start
Common solutions for Whirlpool Dryer Won t Start. The thermal fuse is a safety device designed to protect the dryer from overheating.
If the dryer hums but does not start, the start switch is not at fault. If the dryer does not respond or make any noise, the start switch could be at fault.
Terminal Block Problem
A dryer that blows fuses or trips circuit breakers could have a problem with its connection terminals. Check the wires inside and outside of the terminal block for signs of burning wiring or loose connections.
If so, repair and tighten any wires with damaged insulation, but if the connection terminals inside the terminal block itself have burned up, you’ll need to replace this common issue space heater part.
Door Gasket Issue
The drying machine’s door has a gasket to keep the hot air inside and prevent the cold air from getting sucked in.
If this piece of rubber has been worn out, you will have to get yourself a new gasket and replace it as soon as possible because it causes your dryer to work poorly, as well as make it inefficient.
To check if your gasket is acting up, take a piece of paper and see if there’s any wind or breeze coming through the door when the machine is set on medium heat.
If you feel that a part of your appliances isn’t doing its job just right and could use some decent sprucing up, take care of replacing it with a brand new one.
Cycle Settings Incorrect
Many washers have multiple washing settings, some of which can delay the start or mess with your detergent.
If you notice that the controls on your Hotpoint washer aren’t responding and/or the machine seems stuck for a long time, restore power to reboot it so that all settings are cleared before doing a wash cycle again.
Simply shut down the dryer by disconnecting from the electricity or unplugging it from your wall outlet, wait a few minutes, then flip it back on and try again.
Start Switch Cause
Before you check out whether the start switch is defective, first try to turn on the dryer.
If it starts humming but fails to start completely, it tells you that the problem may have something to do with the starting switch.
However, if this doesn’t happen, then there could be something wrong with the drum or one of its internal parts.
This is why we recommend testing the starting switch for good continuity by using a multimeter. This can help you detect whether it has any sort of issues and if so, replace it immediately.
Faulty Door Switch
The door switch is activated when the dryer door is closed. On most dryers, the door switch makes an audible clicking sound when it activates.
To determine if the door switch is working, try starting your dryer and then listen for a “click.”
If you don’t hear a click, this means that there may be something wrong with it, and you should use a multimeter to check its status.
If it doesn’t have continuity, this means that the door switch is defective and should be replaced immediately.
Defective Drive Motor
The drive motor turns the drum and blower wheel to extract the air moisture. Before replacing the motor, first, check the thermal fuse, start switch, and door switch.
If all of these parts are working properly but the motor is making a humming noise, remove the belt from the motor and check.
If there are any obstructions in the blower wheel. If there aren’t any obstructions to the blower wheel, then it could be a problem with the dryer’s motor. To find out we have to replace it.
Error In Main Control Board
The main control board might be defective but it’s not the most common problem.
There are other parts that have a tendency of breaking down first, but replacing these is often futile if the main control board is at fault.
Try to figure out which other parts might be responsible beforehand by testing the functionality of these components thoroughly.
Hotpoint Dryer Won’t Start
Related Guide