Frigidaire Washer Won’t Spin

Frigidaire washer won’t spin. Washed clothes are soft and clean, but this isn’t always easy to achieve when doing laundry by hand.

One must operate pretty much every aspect for this to happen, including the washing process itself, which involves adding detergent and loading your clothes into the machine.

If you’re not getting distracted while operating the washer, you’ll be able to tell if it’s spinning or agitating properly.

You may find that one or both of these components aren’t working effectively in your model washing machine.

When this happens, consider having your transmission repaired to get back up and running in no time.

Frigidaire Washer Won’t Spinfrigidaire washer won't spin 2022

Frigidaire wash won’t spin or agitate. Inspect the drive belt to determine if it is broken or loose on the pulleys. If the drive belt is loose, replace it with a new one. If the lid switch assembly fails, the washer will not spin.

We have listed some tips below on how to fix the Frigidaire Washer when it doesn’t spin

Tub Bearing Damage

At the back of the drum of most Frigidaire washing machines is a tub bearing. It is a metal joint that holds the drum of the washing machine in place while it agitates and spins.

As the bearing moves with the drum, if it begins to wear down, it may begin to screech or squeal – meaning you should be careful not to let this happen to your washer. The drum will eventually stop spinning altogether if the noise isn’t addressed.

While it can also be the result of other factors, friction is the most common cause of this problem. Unintentionally rubbing against one another can cause friction, which can build up heat and result in a burnt smell.

But don’t worry. As long as you are covered by a Frigidaire warranty, a Frigidaire repair service representative will be able to replace any defective tub bearings for you.

Motor Pulley Brokenmotor pulley broken

A Frigidaire washing machine has a motor pulley that keeps tension on the belt so it doesn’t slide down the drum when the washer is running.

If this piece breaks, the belt will lose control of the drum and can’t rotate it. When this happens, the loose belt may rub against the motor pulley and produce a slight burning smell until the drum finally stops spinning.

Contact an authorized Frigidaire repair specialist to get your washing machine’s motor pulley examined and repaired if needed. The technician may also suggest that you change out the belt if it suffered damage in this malfunction.

Faulty Motor drive

The motor located inside the washer is very useful. It drives the whole machine and makes it possible for the washer to run.
Sometimes it can be affected by some problems and will start behaving badly after some time. One of the most common problems with washing machines is that we try to operate them at too short intervals.
Then we start having problems like not enough water flow or spinning that won’t stop at all and will not allow us to dry the clothes properly.
This is a really big problem, especially on these cold days so before you go out shopping for a new one, check out our great step-by-step guide on how to fix your washing machine.

Stator Assembly Problem

The non-circular object (stator) interacts with the circular, rotating mass (rotor) to create a magnetic field that gets the tub in the washing machine spinning.

If something goes wrong in this process, your washer will not be able to wash or agitate. Inspect the non-circular object for damage since it has metal parts inside, so you can check its inner workings.

Motor Control Board

Motor control boards provide electricity to motors, and if the motor control board is malfunctioning, this can lead to problems being experienced with a specific appliance.

A poor motor control board may not provide a power source to the motor, or it could give a low-voltage signal that prevents a washer from performing its regular maintenance properly.

In order to determine whether or not your motor control board is faulty, first ensure the board is providing power to your motor.

If it has power but isn’t giving out enough power to run your motor as normal, then you should replace the board as soon as possible because this might cause further damage to any other components in conjunction with your washing machine.

They will be required much more energy to perform their necessary duties after going through a cycle with a defective/poor-quality motor control board.

Effective Lid Switch Assemblyeffective lid switch assembly

The lid switch assembly keeps a lid from spinning while the washing machine is in operation. It prevents engaging unless it has been put on properly by the user.

If the washer does not spin, check if the lid switch assembly is not working. To do this, use a multimeter to test if there is continuity across its two prongs when it has been pushed on down into the internal socket.

If the lid switch does not have continuity, replace it by removing its mounting screws and removing it from the interior of the washing machine.

Front Loading Washer Repair

Turn off your washing machine and unplug it from the outlet. If possible, turn off the power to the machine at the circuit breaker.

Hold down on the Start or Pause button for 5 seconds and release. Plug your washer back in and turn the power back on again at the circuit breaker so you can resume washing clothes.

Frigidaire Washer Won’t Spin

Related Guides