Frigidaire ice maker not working. Frigidaire makes some of the best ice makers. If you have a Frigidaire refrigerator with an ice maker, your machine probably gives you a lot of flexibility and high levels of convenience.
However, ice makers can sometimes malfunction. When this happens it’s often easy to troubleshoot and fix the problem on your own by following a few simple steps.
Anytime that your ice maker is giving you problems or isn’t working as well as it used to, it’s helpful to first reset it as this helps solve many issues on its own.
Today we’ll teach you some simple ways to troubleshoot common ice maker problems so that you can unlock some secrets before calling for help from an expert.
Frigidaire ice maker not working
A common cause of a clog is ice blockages in the water line. There is also a possibility that the water filter for the ice maker is clogged. Fix: Locate and replace the water filter. Filters for ice makers are typically located inside the refrigerator (to keep them from freezing).
The ice maker Control arm off
If you find your ice maker not working but water does, there may be a reason. The first thing to check is the switch arm.
It controls the ON/OFF feature of your refrigerator’s ice maker and lets you know if there is a problem with it.
This part is sensitive and can get moved by touching the freezer door inside your fridge which will cause an issue with your ice maker because all that accumulates on it will freeze into a large chunk.
Frozen water line in refrigerator
Sometimes, a fridge’s ice maker can fail to operate because of a frozen water supply line. The area where this line meets your refrigerator is usually located behind the device and is often easy for people to miss at first glance.
It’s important that you take a look at this area yourself before calling in the professionals because any problems will likely be easier for you to correct than for them.
You should begin by moving your refrigerator out from its wall or other installation points so that you have more room behind it.
Unplug the unit and turn off its water supply, which will usually involve opening a faucet somewhere else in your home.
Refrigerator water filter clogged
If your ice maker isn’t producing enough ice or the cubes are small, it’s likely due to a clogged water filter.
Before water goes to the ice maker or dispenser, it flows through the filter to get rid of any impurities.
Over time, the filter will reach its capacity and will clog up restricting water flow. Luckily you can easily put an end to this by replacing the water filter.
Locate your model’s specific filter online based on your model number which you can find by looking in the owner’s manual or by locating your Frigidaire model number online for specific instructions on how to do that step-by-step.
Ice maker error code
In order to find out why your refrigerator isn’t making ice, it would be a good idea to check the control panel located inside the fridge.
If you see any error codes displayed there, refer to your owner’s manual or a similar online resource
The information contained there may indicate that a certain part has failed and will need to be replaced in order for ice production to resume.
Faulty Door Seal
When the temperature variation is off-balance in your refrigerator or freezer, it’s sometimes because of a problem that has to do with the seal for the door(s).
Without a good seal, warm air can creep into the fresh food section while cool air escapes out of the freezer.
If the temperature sensor detects this warmer air, you could end up with too much refrigerant running through your compressor which makes it run longer to try and get fresh food back down to the 37-degree mark.
This could make your freezer temperature plummet below zero which will lead to ice buildup on your tubes and valves.
Defective Ice Maker assembly
If the ice maker fails to operate it may be that the Ice maker assembly itself is broken. There are several working parts inside the control module of the ice maker which can cease to work completely, and most are not sold separately.
Also, ice makers have a relatively short lifespan, and may not always be worth fixing. If simpler, more straightforward parts like the water inlet valve or shut-off arm have been ruled out as faulty possibilities.
There is no mention of either on the warranty for the device at hand, replace it as a whole with an updated model instead of repairing it.
Icemaker Module issue
The icemaker module is relieved of its duty once the temperature of the water has reached 15 degrees Fahrenheit in ice trays.
Once this temperature is reached, the motor switches on and dispenses the cubes in the ice bucket.
The flow of water to comprise a cycle begins when the module releases either electrical or magnetic power to the inlet valve and ends when the next cycle starts.
If there’s an issue with your machine, just check whether or not your machine’s thermal sensor is faulty by turning it off for two minutes and then switching it back on again.
Then repeat this process three or four times to double-check that your remote sensor is faulty. Make sure your refrigerator’s power switch is turned on and if you have an icemaker with ejector blades, make double sure that ice cubes aren’t stuck within them.
If all else fails, troubleshoot through test points in the icemaker module until you locate where exactly there’s a fault in one of its circuits.
Icemaker mold thermostat
If your fridge doesn’t have ice, the ice maker should be checked. Ice makers consist of a Thermostat that measures the temperature of the ice mold (ice tray) and activates an ice harvest cycle when it has reached temperature.
When this happens, water is released into an ice mold that then freezes to create blocks. If the thermostat is defective, the ice maker won’t start making any more ice.
The Thermostat can be tested for continuity. Replace it if necessary to get your household back up and running.
Frigidaire ice maker not working
Related Guides