Frigidaire Dryer Troubleshooting

Frigidaire Dryer Troubleshooting. If you’re looking for help fixing your Frigidaire Dryer, look no further.

Our comprehensive Frigidaire Dryer Troubleshooting guide will not only familiarize you with common issues and provide tips and tricks on how to repair them, but the Troubleshooting manual can also function as a convenient and durable reference when dealing with issues related specifically to your dryer model.

Frigidaire Dryer Troubleshooting

frigidaire dryer troubleshooting

We discuss some problems with the Frigidaire dryer here to troubleshoot it.

Frigidaire Dryer Will Not Heat

The igniter is an important part of the dryer’s heating unit. It uses heat to ignite the gas that causes the burner assembly to heat up and radiate heat into the dryer drum.

If the igniter fails to provide heat, the burner will not light and produce hot air which prevents clothes from getting dried.

To know if the igniter has burned out you can use a multimeter to test it for continuity once taken out from its place within your appliance.

If you fail to get any kind of proper response or reading after testing it like this, then that means your igniter has finally stopped working. You would need to replace it in order for your appliance to work properly again.

On gas dryers, the flame sensor is used to detect heat in the dryer. If the sensor is defective, it won’t allow for heat to be created.

To check if the flame sensor is bad, first check the thermal fuse and igniter. It’s possible that if either one of these is bad, not enough heat will make its way to the flame sensor and it’ll produce a false reading.

Once you double-check these parts, you can test your flame sensors with a multimeter at room temperature to see if they have continuity or not. If they don’t then these need replacing.

Frigidaire Dryer Will Not Stop

heating element

The heating element is what heats the air before it enters the dryer drum.

Over time, a faulty heating element will cause certain parts of the dryer to wear out and stop working properly.

If the heating element isn’t working, your clothes could take longer to dry than usual, possibly resulting in mildew or mold.

The best way to tell if your heating element is faulty is by testing for continuity with a multimeter. This will help you determine if you need to replace the heating element in your dryer or not.

The cycling thermostat cycles the heat on and off to regulate the air temperature. If the cycling thermostat is defective, the dryer will not heat.

However, this is rarely the case. Before replacing the cycling thermostat check all of its more common malfunctions first.

If you have determined that all of its other parts are working properly for example that it’s getting power, check its continuity by using a multimeter to test for resistance.

If you have determined that there is an issue with any part of its wiring or whether it’s even receiving power, replace it.

Frigidaire Dryer Will Not Start

The start switch is the first place to check if your dryer is not turning on or making any noises during its drying cycle.

First, attempt to start the dryer and see if it responds. If it motors but does not start, then there could be a problem with the start switch.

Measure the start switch for continuity with a multimeter. If you do not have continuity in your measurements, replace the start switch.

The dryer drive motor rotates the drum and blows air out, but first, check the thermal fuse and start the switch.

If they are working properly, remove the belt from the motor to see if there is an obstruction near the blower. If there isn’t any obstruction, replace the motor; if so, you may want to take a look at it.

Frigidaire Dryer Runs Too Long

The cycling thermostat regulates the drier’s temperature by turning it on and off. If the cycling thermostat is defective, there is no heat.

However, this is rarely the case. Remove other parts before replacing a defective cycling thermostat by checking to make sure all of the other components are working properly.

Test for continuity using a multimeter if you cannot find anything wrong with these parts because if there is no continuity the cycling thermostat needs to be replaced.

The moisture sensor monitors the clothing’s level of moisture and sends a signal to the control board to shut off the dryer when the clothes are completely dry.

If the moisture sensor is malfunctioning, it could inaccurately report that the clothing is still moist, causing the dryer to continue running even though it should be turned off.

However, this is rarely an issue. Before replacing the sensor you should check all more common parts. If you have determined that all of these are working properly, replace your moisture sensor.

Frigidaire Dryer Troubleshooting

Related Guides

Leave a Comment