Frigidaire dishwasher not draining. The Frigidaire dishwasher has found its place at the top of the market for a reason.
They are among the most popular brands out there, but recently it seems that customers have begun to complain more.
Stories regarding dishwashers not draining properly are becoming ever more frequent, and this is due partly to different operation problems which can easily strike any day, no matter how well-maintained the appliances are.
Frigidaire dishwasher not draining
Sometimes a Frigidaire dishwasher that is not draining water is due to an air gap or garbage disposal clog and is not actually a dishwasher issue.
Water may cause then backflow into the dishwasher during a wash cycle. Running the disposal before starting a wash cycle can clear the drain of debris that can block water flow.
Follow it with me below if you’re feeling handy or just want your appliance repaired.
Standing water in the filter area
You may see water in your dishwasher area. This is where the machine keeps its important seals wet and safe from drying out.
The water drains when a cycle starts and is replaced with fresh water at the end of the cycle when your dishes are being cleaned.
Defective Drain Pump
The drain pump uses an impeller to force water through the hose. If the pump is not working, it will cause excess water to leak onto the floor during the drain cycle.
To determine if the pump needs to be replaced, check the continuity of its wires using a multimeter. If there is no continuity or if it’s getting power but won’t run – replace the pump.
You should also check for debris in the hose or other physical damage that might be causing a drain pump failure.
Air gap issue
The air gap allows air into the dishwasher to drain water. It fits over the sink and serves its purpose without interrupting anything.
If there is a clog or blockage, it will cause water to back up into the sink, potentially causing backups in other areas of the home. Check the manufacturer’s instructions when troubleshooting an air gap.
Defective Drain Impeller
A drain impeller forces water through a hose into the garbage disposer.
Replace the impeller if it is damaged.
Faulty Pump and Motor Assembly
When the motor is engaged, it spins a small propeller that will move water and mud out of the way of the pool’s drain line.
If this system fails to work properly, there might be debris in the drain line, such as leaves pooling above the exit grating at the bottom of your swimming pool.
If the drain motor doesn’t run or won’t turn on, further inspection of your pool’s lines might be necessary to ensure there isn’t any sort of obstruction.
Drain Valve issue
Over time, the drain valve can get clogged with debris. The best way to ensure that water can flow through the drain valve is by cleaning out the debris.
If the drain valve is clean, but it still won’t actuate, it means it’s time to replace it. Drain valves are not repairable, so if you need to replace your old or faulty one, then do so as quickly as possible because if you don’t, then your water pressure could fizzle out.
It’s best to invest in a replacement early rather than later; otherwise, you risk having to take sizeable steps backward every time you’re forced to use your sink or bathtub until you’ve bought a replacement.
Check Valve fault
If a valve fails to open and allow the water to drain, it will lead to a backup of water which could cause damaging leaks or flooding.
One way that can occur is if the dishwasher’s check valve is not functioning properly. In that instance, try cleaning out the valve and replacing it if necessary.
Check Ball problem
If you’ve noticed water collecting after your dishwasher has completed a cycle, this is probably due to the check ball becoming lodged in the drain valve.
If, for any reason, water doesn’t seem to be draining as quickly as it normally does, then chances are that the check ball may have become jammed or stuck inside of your drain valve and maybe obstruct water from flowing out of your dishwasher.
Garbage Disposal that is clogged or incorrectly installed
If you recently installed your garbage disposal, the drain plug may not have been completely removed. All disposers are manufactured with a solid plug in their own drain tube.
If you connect your dishwasher to the disposer, then the plug must remain stuck in the drain tube. However, if you don’t connect it to the disposal, then the plank must necessarily be removed from the end of the hose fitting stuck in the disposer’s drain hole.
If you haven’t replaced your disposal for quite some time now, there’s a chance that it is clogged up. To remove the hose connector from within the disposal and clean out both its connection cavity and hose tip at your disposer’s end too.
These are most likely spots where blockages occur if your dishwasher will not empty.
Frigidaire dishwasher not draining
Related Guides