Frigidaire dehumidifier not working. Frigidaire dehumidifiers are helpful in getting rid of the moisture in the air within a room. While any other electric home appliances tend to occasionally have some problems,
this brand has some of the most common ones with owners reporting it could lose power, be unable to detect humidity levels, stop running or have a faulty fan motor.
In case your Frigidaire dehumidifier starts to not work properly because its control board is damaged, you should know that this can easily be fixed yourself by replacing the defective one with a new one.
Frigidaire dehumidifier not working
Frigidaire dehumidifier not working. By doing so, you will restore power and prevent further damage from occurring.
Still, if you aren’t too sure about your abilities when it comes to electrical things such as mechanical repairs.
We would advise against touching anything inside your Frigidaire unit unless you really know what you are doing because malfunctioning parts can cause further issues for your product.
The bucket switch has no continuity
As long as the bucket is half full, the switch won’t have any effect on the operation of the dehumidifier.
The switch only activates once it senses that the water is reaching a height that it shouldn’t exceed.
What you want to look out for here are two things: if your dehumidifier fills up too fast or if it fails to run at all.
In case there’s a problem with it, you can use a multimeter (a device used to measure electrical current) to test whether the bucket switch has continuity and isn’t stuck in an open position.
If it doesn’t have continuity, then you’ve found your culprit and need only replace the part
responsible for regulating the flow of water into the bucket using a multifunctional screwdriver with adjustments for different sizes of screws.
The trouble with incoming power
There might be a problem with the electrical outlet. A few steps you can take to diagnose the issue. Make sure the electrical appliance gets power (i.e., turn it on) by first plugging it into the outlet.
If there doesn’t seem to be power coming out of the outlet, inspect your electric circuits and see if you can see what’s wrong (could be a blown circuit).
Humidistats do not have continuity
A humidistat is a moisture sensor – it monitors the amount of water vapor in the air and relays that information to your building’s system to determine if any specific actions need to be instituted (like turning on the humidifier).
Because the level of humidity can vary from room to room, you might have more than one humidistat installed in your home.
If you find out that one of these devices isn’t communicating with other parts of your HVAC system (or none at all),
check continuity between each lead and its respective terminal to see if they’re touching. If they aren’t, replace the defective device and you’ll get things back up and running smoothly.
A humidity sensor is defective
The humidity sensor is monitored for changing conditions in the air. In cases wherein the degree of moisture gets too high, contact closures will occur in the device to kick on the dehumidifier.
If there is a problem with the humidity sensor, it may prevent the dehumidifier from running appropriately.
Faulty Control Board
The central control board monitors the moisture level inside the air. If this moisture level becomes too high, it will trigger the dehumidifier to start working.
However, if one or more components on the board are out of order then it might not be able to
carry out its task of lowering the moisture in the air within your home and you’ll most likely notice that your home is a bit damp and humid which can lead to any number of problems.
Defective Compressor
The compressor is a pump that compresses refrigerant and circulates it through the evaporator and condenser coils. It’s interconnected with other important components in your system.
So if it’s not functioning properly or at all you’re going to find that your dehumidifier isn’t performing up to its full potential.
Besides having it on hand for when you need it, regular maintenance can reduce the chance of
needing to replace it altogether especially repairing the more common components such as clogged drains or replacing older fans that may have been malfunctioning.
If you follow this advice and manage to avoid further complications by avoiding additional damage then chances are good that you won’t need to replace the compressor after all.
Related Guides