Electrolux Dishwasher Won’t Start

Electrolux Dishwasher Won’t Start. The convenience that comes with owning a working dishwasher cannot be overstated. However, when you’re faced with discovering that your Electrolux dishwasher won’t start, it can be so nerve-wracking.

Don’t worry though. Whether the fault lies with a defective door latch or a blown thermal fuse, our guide will help you understand why your Electrolux dishwasher isn’t running.

If you’re asking yourself “Why won’t my Electrolux dishwasher will not start? is the answer one of several common problems?

Electrolux Dishwasher Won’t Startwhy electrolux dishwasher won't start

We discuss some problems that occur with Electrolux dishwashers that refuse to start in this article.

Test The Power Supply

If the dishwasher doesn’t turn on at all, this is probably due to a power supply problem. The circuit breaker may have tripped off so go ahead and reset it. If it hasn’t tripped, make sure your appliance is properly plugged into its wall outlet.

It may involve you pulling out the appliance just so that you could disconnect the clips underneath to look for any signs of damage or anything that might be preventing a secure connection to the wall socket.

Issue With Timer

The timer is a vital part of your dishwasher. It allows for the pump to run at the right time and for enough power to flow into it. If the timer is incorrectly set or is faulty, it won’t send electricity throughout the machine causing your dishwasher not to start out.

It is important to note that many times timers are misdiagnosed, so always check all typically faulty parts before replacing the timer. Just like with other kitchen appliances, it can be easy for small mishaps like these to occur.

If you catch them early and know how to reset and fix them, you can save money without sacrificing performance or convenience.

Dishwasher Should Be Reset

​ If you’ve interrupted the wash cycle of your dishwasher and now it won’t restart, it could be stuck between cycles. Sometimes when this occurs the lights on your dishwasher will flash, other times.

Nothing happens at all. The next thing to try is turning off the power to the appliance and then back on again. If that doesn’t work, check the instruction manual for resetting your dishwasher.

You may need to press and hold the Start button or unplug the unit for at least a minute or so. After that’s good, you’ll be able to start a new wash cycle on your dishwasher.

Exmine Selector Switchexmine selector switch

The selector switches determine which wash cycle settings each load will receive, and the selector switches are normally located on the control panel.

Test each button separately by touching the probes of your multimeter simultaneously to both sides of the switch while the button is selected and both probes are in their respective positions.

A reading of infinity should be produced when the toggle switch is in its resting position, but then a reading of zero should be generated when you press the button alone.

Replacing the defective selector switch is necessary if any other readings are obtained.

Defective Thermal Fuse

An important component of the dishwasher is the thermal fuse. When it detects that the appliance is overheating, it will cut off power to protect itself and its surroundings from sustaining unnecessary damage.

Once warmed up, if there’s a problem with your thermal fuse trying to turn back on and restore power, the circuit board may be at fault in that case you need to call for assistance.

A lot of the time it will just take a simple basic electrical test by a technician to let you know whether or not replacing your thermal fuse will solve your issue.

Faulty Main Control Board

The main control board is the pilot light that keeps the flame of your dishwasher burning. It often provides power to several components, including a motor and many electronics that monitor what’s going on with your machine.

It is possible that this part could malfunction, preventing the dishwasher from starting. Before replacing the main control board oftentimes more expensive parts will go bad like wiring that fails or breaks down over time making sure you make a thorough investigation first can save you money in the long run.

Failure Of Motor Start Relay

The motor start relay is an important part of a dishwasher’s start-up process. When you take it apart, search for a magnet or other mechanism that activates the relay when the pump starts up; this will help you to understand how it works later.

As with everything else in your dishwasher, electricity is the power source behind the dishwasher switch mechanisms and they are all interconnected.

Take some time to review the diagram to fully understand it and compare it to your readings as you dismantle your dishwasher parts. Take notes, have fun, and enjoy learning more about electricity.

Related Guides

Leave a Comment