Craftsman Snowblower Won’t Start

Craftsman Snowblower Won’t Start. Craftsman snow blowers are complex machines with many moving parts. Because of this, you might have to make repairs when something goes wrong.

There are some problems that can be easily avoided, so it’s important to address them before they get out of hand.

Don’t neglect these problems when they arise because they will eventually have an even greater impact on your time and resources if they aren’t addressed.

In order to avoid Craftsman snowblower problems that should be fixed as soon as possible, you need a professional to come over with the necessary equipment to repair any malfunctioning system without fail within the same day or at least the next business day – our craftsman repair services are the best around.

Craftsman Snowblower Won’t Start

craftsman snowblower won't start

The engine cannot start if the spark plug is defective or if the carburetor is clogged.

And if there is no fuel going through the carburetor, then it might be clogged and that’s why it won’t start.

If your snowblower has been sitting idle for some time and won’t start, try clearing out any old gas from the cylinder and make sure not to leave any fresh gas sitting in there for too long.

In this article, we explain how to fix a Craftsman snowblower that won’t work.

Carburetor Cleaning

If none of the steps above have gotten your Craftsman snowblower running, then you may need to clean the ice buildup in your carburetor more aggressively to dissolve gunk and residue.

A carburetor’s purpose is to combine air and fuel in a precise ratio for efficient combustion, so if it’s clogged with residue, it can’t do its job.

Check your owner’s manual for instructions on how to access the carburetor, which is behind the air filter cover.

After removing both the cover and air filter (you’ll see a cylinder-like opening), you’ll see the Craftsman snow blower’s carburetor (a metal case with a cylindrical opening).

Damage Fuel Line

Fuel lines, which connect the gas tank to the carburetor, should be flexible and pliable. If they become hard or cracked, they may kink.

If that happens, your Craftsman snowblower may not start up or operate properly because not enough fuel will reach it to run it properly.

If you use ethanol gasoline, these concerns are even more important because this type of fuel tends to eat rubber materials over time and be particularly corrosive.

You must replace any deteriorated line with a new one. It’s much better off getting a clear view of what is going on inside your business.

Drain And Replace Old Gas

Since your Craftsman snowblower has been sitting unused for the past several months, you may have trouble getting it to run because the gas might have developed a gummy residue.

Using a small hand pump, siphon out the used fuel until you come across fresh fuel, then refill and start the engine again.

Defective Spark Plug

defective spark plug

Make sure the spark plug is intact and in good condition because if it isn’t, the engine has to operate on a less than the optimal amount of energy.

With friction on its way up during the combustion process, the machinery could seize up entirely and you won’t be able to use it at all.

So keep an eye out for split insulators or damaged electrodes for starters, but leave no stone unturned and check for heavy carbon buildup as well.

A quick investigation should tell you whether or not your spark plug needs replacing. A faulty one will have no spark when put under test.

Ignition Coil Issue

ignition coil issue

The ignition coil connects with the spark plug while the engine is running. If this part stops conducting voltage to the spark plug, your car may stall.

Before you replace it, ensure that your spark plug works by testing it yourself (or getting someone to do so).

Once you’ve confirmed that the spark plug is working properly.

Use a diagnostic tool called an ignition coil tester to diagnose whether your replacement part needs to be replaced at all or not.

If you find that the ignition coil needs repair or an outright replacement, then it should either be repaired or replaced respectively and you can finally put all of this behind you.

Faulty Flywheel Key

It is possible that the flywheel key has been sheared in half. Flywheel keys have a small metal piece that engages with the flywheel when placed in the crankshaft.

Craftsman Snowblower engines stop suddenly, and the flywheel key snaps in half to prevent damage to the engine.

Examine the flywheel after removing it from the engine to determine whether it has a broken key.

In the event that this metal key, which is located on either side of the blade housing, does not appear whole due to being crushed or snapped, or severely cracked, it will need to be replaced.

Recoil Starter Error

recoil starter error

If the starter rope is pulled and released, it will give the recoil spring some opportunity to recoil back onto a pulley.

If the engine doesn’t start because there’s a problem with either the rope or the pulley, it might be because of an issue with your starter assembly.

Many starters have individual components that work together to get a car started, such as engine boxes or recoil springs for example.

If you think replacing your starter assembly would be beneficial, then we suggest checking out different models we have so you can find one that fits your needs.

Craftsman Snowblower Won’t Start

Related Guides

1 thought on “Craftsman Snowblower Won’t Start”

  1. Youre so cool! I dont suppose Ive learn anything like this before. So nice to seek out any individual with some original ideas on this subject. realy thanks for starting this up. this website is something that is needed on the net, somebody with a bit of originality. useful job for bringing something new to the web!

Comments are closed.