Amana dryer not heating. There is nothing quite like the feeling of putting on warm clothes straight from the dryer. But it can’t happen if your dryer isn’t heating or drying your clothes properly.
Let us help you feel as if you are unwrapping that fresh-from-the-dryer feeling again by giving you tips and tricks for making this chore into a more efficient and less time-consuming process.
Amana dryer not heating
Over time, the heating element could burn out and you will be required to replace it. You can check if the heating element is faulty by testing its resistance. If, however, the resistance is too high or too low, replace it immediately since this is not a safe option for use.
The heating element warms the air before it enters the dryer drum so the machine can dry your clothes more quickly.
Deficiency in gas valve solenoids
Gas dryers have two or more gas valve coils. These coils switch on and off to let gas into the burner area. If any one of these coils stops working, it’ll result in no heat being produced by the dryer unit at all.
To find out which specific coil has stopped working, you need to check the igniter (the part of the gas valve assembly that lights up whenever you turn on your dryer).
If you don’t see any flames when you turn on your dryer but instead see only a glowing coil, there’s definitely something wrong with that particular coil.
However, if nothing happens when you turn it on, then either all of the coils are faulty, or perhaps there’s something else wrong and a replacement is needed elsewhere like perhaps one of the thermal fuse units or maybe a bad cord itself?
A thermal fuse has blown
To prevent the dryer from overheating, a thermal fuse is used. This is a safety measure that prevents your appliance from accidentally burning itself out if something goes wrong.
There are various locations for the fuse on dryers; you should have been given instructions on its placement at the time of purchase, and you can find them in your owner’s manual as well. In the event of a blown fuse, there is no continuity in the circuit.
If you believe your dryer is having this issue, you can use a multimeter or continuity tester to check for any problems that may be causing it.
If you suspect a thermal fuse problem, you should inspect the exhaust vent to see if the lint or dust has blocked it. If so, you should clean it out beforehand.
The flame sensor is defective
If the flame sensor or other components that detect thermal energy aren’t working on a dryer, the heat won’t circulate throughout the machine.
To find out if they are defective, use a multimeter to confirm that they are getting electrical power at room temperature. If they don’t get electricity when disconnected from circuit points, replace them.
The igniter lacks continuity
Dryers have to have a source of ignition in order to heat up and use the heated air that is blowing inside the appliance to continue drying clothes.
The part which creates the flame is called an igniter, and it’s one of the most important parts of any dryer. It makes sure that your garments are dried thoroughly at high temperatures so they don’t get damaged when put in the drier.
The igniter is usually attached to the heating element, but they can sometimes work separately as well. It burns off due to pure resistance from being used over and over again.
When this happens, you need to consider getting a new one for your dryer so that it will continue working efficiently for you.
Problems with the power supply
If your dryer is not heating, then there might be an issue regarding where you plug it in. Dryers generally utilize two prongs which are supplied by the N/O terminals on a socket in most cases (and sometimes a neutral wire as well).
Some buildings do different things with their wiring so check to make sure that you’re dealing with the 240 volts required by your dryer.
The fuse box or circuit breaker should be checked as well since either could be responsible for tripping and leaving your dryer powerless when something goes wrong.
Faulty Heating Element Assembly
In a dryer, the heating element assembly heats the air before it enters the drum. It is possible for a dryer’s heating element to burn out over time, resulting in no heat.
You can test if the heating element assembly has burned out by placing your multimeter in resistance mode. When your readings indicate that the heating element assembly oven is defective, you will need to replace it.
Defective timer
If your dryer isn’t heating, there may be a problem with the timer. However, this is rarely the case (usually it’s something else). Before replacing the timer, check all of the more frequently defective components.
If you determine that all of these are working as expected, test the timer by using a multimeter and consulting the wiring diagram to determine if there’s an issue with it. If the problem lies within your timer, replace it.
Main Control Board issue
There may be a problem with the main control board. Rarely is this the case? Make sure all of the more commonly defective parts are checked before replacing the main control board.
Ensure that all of the other components are working correctly before replacing the main control board. It is not easy to test the main control board, but it is relatively simple to check for signs of burning or a shorted component.
Amana dryer not heating
Related Guides