Admiral Oven Won’t Turn On. Ovens are among the most important appliances in the kitchen – you might not use them every day but just think about how impossible it is to get through a single week without one.
Whether you’re baking up a batch of cookies or a loaf of bread, or simply easing off after an exhausting day at your job by having a frozen pizza instantly heated up.
You need your oven and when something goes wrong with it, you definitely need to know how to repair it and whether it’s time to have a pro take over.
Here’s your step-by-step guide on fixing seven out of the most common problems that can arise with an oven.
Admiral Oven Won’t Turn On
If an oven won’t turn on there could be an incoming power problem. To locate the underlying source of a potential electrical problem such as this one, you can use a multimeter to test the incoming power at the wall socket. You need to know that the thermal fuse trips if the oven overheats. If it has blown, the oven will not turn on.
We discuss some problems that occur when the Admiral oven won’t turn on here.
Thermostat For Temperature Control
The temperature control thermostat regulates the temperature in your oven by cycling on and off the bake and broil element.
In case there is no signal coming back from it, then it might be a sign that this component isn’t working. But that is not a common issue.
Before replacing it, check other components with higher failure rates – specifically igniter and the upper and lower broil elements.
If you find these are working properly, then you should replace your temperature control thermostat. The best way to test the thermostat is somewhat difficult to do so we suggest replacing it instead.
Problem With Safety Valve
The gas oven safety valve works with the oven igniter to provide gas to the burner. If the safety valve is not working, the cooker will not heat.
However, this is rarely the cause of problems. Before replacing the safety valve, test all components related to heating, especially the igniter.
If it’s working properly and there appears to be a problem with the heating, use a multimeter to test for continuity on the gas oven safety valve. If it doesn’t have continuity and you need to replace it, go ahead and do so.
Issue With Relay Board
Some ovens are equipped with a relay board. The relay board consists of several relays, each of which controls the voltage to the heating element.
If one or more of these relays stop working properly, the temperature in the oven won’t rise as expected.
However, this rarely occurs and usually results from malfunctions related to heating components in the oven itself – so first check all of those and see if any need replacement.
If none of them do, your relay board might be causing the issue and should be replaced.
Defective Thermal Fuse
The thermal fuse will be triggered if the inside of the oven becomes too hot. If it’s been tripped, you have to replace it to allow the oven to function normally again.
However, this isn’t something that happens very often and you shouldn’t worry about it. To test for continuity, use a multimeter on the fuse and see if your oven works as normal when it has power.
If it doesn’t work, then you need to remove it and insert a new thermal fuse with the same rating. You mustn’t reset or try to repair the fuse it is important that you don’t tamper with this part.
Broil Element Fault
When the broil element is heating properly, it glows red hot. If the element does not glow red, this indicates that the element may be heating at a much slower rate than usual.
If you are having other problems with your oven, there may be something else going on as well. First, check to make sure there aren’t any holes or blisters in your broil element.
This could indicate that it has burnt out or is close to doing so. To test whether or not your broil element has burned out, use a multimeter to perform a continuity test on the element.
Bake Element Malfunction
When the bake element heats up sufficiently, it will glow red. If you do not see this happening, the element either is not getting enough power or has burned out.
In the case of a burnt-out element, it may appear dark and/or charred. Inspect it for holes or blisters. To find out if an element has shorted out, use a multimeter to check its continuity.
In the event that an element is found to be non-functional, you need to replace it as soon as possible in order to avoid any further damage to your oven. Admiral Oven Won’t Turn On.
Related Guides
